NEW DELHI: Zebronics lists the PEX01 PoE extender at Rs 1,899, including tax. It is an inline accessory for extending a compatible powered network connection. Before specifying it for a CCTV cable run, confirm the required link speed in writing: the official page's feature description and detailed speed field do not agree, so this guide makes no throughput claim for the PEX01.

Model and listed priceZeb PEX01: Rs 1,899
Device typeSingle-port PoE extender
Supported PoE protocolsIEEE 802.3af/at
Published power ceiling30W maximum
Published distance ceilingUp to 100 metres
Listed enclosure dimensions9.6 x 2.7 x 2.3cm, without cable caps
Listed net weight60g
Package contentsExtender and 2 cable caps

Price as of 19 November 2026, 02:38 IST. The page gives a single price for the extender, without differently priced cable-length or performance variants. The unresolved speed wording is a reason to seek model-specific clarification before ordering for a speed-sensitive installation. It is not a reason to fill the gap with a specification from a similarly named device.

Identify the job the extender must do

Start with the camera position and trace the installed or proposed network cable back towards its power source. Mark the point where the extender would sit. For a gate or staircase camera, include the route through ducts and around walls rather than estimating only the distance between the buildings. The placement must work as part of an actual cable route, with somewhere accessible for the connection.

An extender is only one item in that route. Ask the installer to identify the source of PoE power, the camera receiving it and the network equipment handling the video. The work order should name the exact devices and explain the intended connection sequence. That makes the proposal reviewable if the camera subsequently loses power or stops delivering usable recordings.

Check power compatibility as well as connectors

The PEX01 page lists RJ45 connectivity and the supported PoE protocols. Use those specifications to ask whether the existing power source and intended camera are compatible. A matching socket does not answer the electrical question by itself. Do not assume that an unlabelled powered network connection uses the arrangement required by every device that can physically connect to it.

The published power figure is a ceiling, not evidence that any camera will receive its required power at the end of an unspecified installation. Ask for the complete power requirement and proposed cable arrangement to be checked together. The installer should be able to explain why this particular extender belongs in the plan and which test will demonstrate that the camera remains usable under its normal operating settings.

The supplied cable caps are part of the package description. They should not be read as an outdoor protection certification. The readable product page does not provide an ingress-protection rating that establishes suitability for an exposed location. For an outdoor camera route, ask the installer to specify how the connection will be protected and kept accessible for inspection, rather than treating a small enclosure as weatherproof by appearance.

Resolve the speed wording before installation

Save a copy of the product listing with the quotation and ask for confirmation against the exact PEX01 model. State what link performance the intended camera connection needs. If the supplier cannot resolve the inconsistent wording, choose a device whose documented specification meets the requirement. This guide deliberately leaves the disputed numerical speed out of both the facts table and the headline.

The same care applies to the stated distance ceiling. It should not be multiplied into a claimed total network reach without documentation for the complete topology. Ask how each cable segment will be measured and tested. A cable connection that produces a picture during a quick demonstration has not necessarily established the stability required for unattended recording.

Compare the alternative by its actual role

Zebronics separately lists the PEX02 at Rs 2,999. Its readable page describes a dual-port extender, a maximum data rate of 100Mbps and support for the same PoE protocol family. It is therefore a distinct model to assess when the proposed route calls for a different connection arrangement. The higher price does not establish that it automatically resolves every requirement left uncertain on the PEX01 page.

At handover, ask to see the saved recording from the camera using the extended route, including the operating mode normally used after dark. Label the connection points and keep the final cable diagram. If the camera later disappears, those records help distinguish an extender connection problem from a recorder setting, camera fault or issue elsewhere in the network.

For related planning, see our Zeb IPPBSL5 vs IPPDSL5 price: IPPDSL5 starts lower at Rs 5,199, Zeb WFPT3M vs WFPD3M price: WFPD3M starts lower at Rs 5,599 and Zeb 36CHV2S8TA8M price: Rs 26,999 for a larger IP CCTV system. The extender decision should follow the camera and wiring plan, with compatibility established for the exact equipment being installed.

Official sources: PEX01 product page and PEX02 product page.