NEW DELHI: The Zeb 8PPG2UGS PoE switch is listed at Rs 9,999 on Zebronics' official website. It combines powered camera connections with separate network uplinks. For a home CCTV installation, the useful starting point is a written camera-and-cable plan, followed by a power budget for the devices that will share the switch.

Listed modelZeb 8PPG2UGS
Official listed priceRs 9,999, tax included
Camera-facing connections8 Gigabit PoE ports
Other network connections2 Gigabit Ethernet uplinks and 1 SFP slot
Power budget150W maximum across the switch
Per-port ceilingUp to 30W
PoE standardsIEEE 802.3af and IEEE 802.3at
Published size and weight19 x 12.5 x 4cm; 610g

Price as of 19 November 2026, 02:35 IST. The official page presents this as an unmanaged PoE switch. It is a separately priced network device, rather than a package containing cameras, a recorder and storage. No alternative configuration price is displayed on this particular model page.

Draw the camera network first

Put every planned camera on a sketch of the property and mark the intended cable route back to the switch. Include the gate, staircase, parking area and any indoor position that actually needs recording. This exercise makes it easier to distinguish a network connection that will power a compatible camera from a connection intended to carry traffic towards the recorder or router.

The dedicated uplinks are useful because the recorder path can be planned separately from the powered camera positions. The SFP slot is another connection option, but the package contents do not list a transceiver. Ask the installer to specify every required module and cable in the quotation. The presence of a slot alone does not tell you what equipment will be supplied to use it.

Budget power across the whole box

Zebronics gives a total power ceiling and a separate per-port maximum. Read those together. The port limit describes an individual connection; the total budget governs the collection of devices. Do not assume that every powered connection can simultaneously deliver its individual maximum. Have the installer document each camera's required power and check the combined requirement against the switch specification.

That check should use the camera's full operating requirement, including any lighting or other powered features you intend to enable. A camera appearing in the recorder's preview is only the beginning of acceptance testing. Ask for the installation to be demonstrated under the actual settings that will be used, then keep the equipment list with the invoice for later fault diagnosis.

The official standards listed for the switch provide a concrete compatibility question to put to the camera supplier. Obtain confirmation that the intended camera accepts the specified PoE arrangement. The physical network socket alone does not resolve power compatibility. This is particularly relevant when adding a powered switch to a system whose cameras previously used separate local adapters.

Separate cable distance from link speed

The product features state a maximum transmission distance of 100 metres and the technical table specifically gives PoE reach up to 100 metres via Cat.6. The same documentation also contains longer-distance entries for other network conditions. This guide does not turn those entries into a promise that the advertised Gigabit camera connection and power will work over a longer run.

Measure the actual route, including the bends and the length needed to reach mounting points. A straight-line estimate from the terrace to the gate may hide a very different installed cable length. Where the plan goes beyond the clearly described PoE condition, ask for a revised topology and a written explanation of the equipment needed, rather than relying on a general coverage claim.

Check the mounting and the handover

Wall mounting is listed, alongside short-circuit, voltage and lightning protection features. These are manufacturer descriptions, not an independent resilience test. The page does not establish a weatherproof outdoor enclosure rating, so an exposed gate installation should not be assumed suitable. Ask the installer to identify a protected location where the cables and power connection can be inspected without dismantling the CCTV system.

The package lists the switch, power cord and QR code guide. Make the quotation show the cost of cameras, cable, connectors, recorder and storage separately. At handover, label the cable ends and record which camera corresponds to each port. A readable port map can turn a later missing-picture problem into a specific connection check instead of a search through unmarked wiring.

For alternatives, the official PoE collection lists the 8PG2UG1UF 120 at Rs 5,999. Compare its full specification and total power budget before treating it as an equivalent replacement. For the rest of the installation, our Zeb IPPBSL5 vs IPPDSL5 price: IPPDSL5 starts lower at Rs 5,199, Zeb 36CHV2S8TA8M price: Rs 26,999 for a larger IP CCTV system and Zeb AHDPDSL24 price: Rs 2,999 for the home CCTV dome camera provide related reading.

Official sources: 8PPG2UGS product page, official datasheet and PoE collection.